Texas Instruments
Obrázek může být reprezentace.
Viz Specifikace pro podrobnosti o produktu.
TLC2264CDG4
Zobrazit detail DataSheets

TLC2264CDG4

Product Overview

  • Category: Integrated Circuit (IC)
  • Use: Operational Amplifier
  • Characteristics: Low-power, Rail-to-Rail Output, Quad Op-Amp
  • Package: SOIC (Small Outline Integrated Circuit)
  • Essence: The TLC2264CDG4 is a low-power quad operational amplifier designed for general-purpose applications.
  • Packaging/Quantity: Available in tubes or reels, with 2500 units per reel.

Specifications

  • Supply Voltage: ±2.5V to ±16V
  • Input Offset Voltage: 1 mV (maximum)
  • Input Bias Current: 1 pA (typical)
  • Gain Bandwidth Product: 2.2 MHz (typical)
  • Slew Rate: 1.3 V/µs (typical)
  • Operating Temperature Range: -40°C to +125°C

Pin Configuration

The TLC2264CDG4 has a 14-pin SOIC package with the following pin configuration:

___________ VCC | 1 14 | VCC IN1- | 2 13 | OUT1 IN1+ | 3 12 | IN4- IN2- | 4 11 | IN4+ IN2+ | 5 10 | OUT4 IN3- | 6 9 | IN3+ IN3+ | 7 8 | OUT3 ‾‾‾‾‾‾‾‾‾‾‾‾

Functional Features

  • Low-power consumption: The TLC2264CDG4 operates at a low supply voltage and consumes minimal power, making it suitable for battery-powered applications.
  • Rail-to-Rail Output: The op-amp provides output voltage that can swing close to both the positive and negative supply rails, maximizing dynamic range.
  • Quad Op-Amp: The device contains four independent operational amplifiers in a single package, allowing for space-saving and cost-effective designs.

Advantages and Disadvantages

Advantages: - Low power consumption extends battery life in portable devices. - Rail-to-rail output enables accurate signal amplification across the entire input range. - Multiple op-amps in one package save board space and reduce component count.

Disadvantages: - Limited gain bandwidth product compared to higher-end op-amps. - Slightly slower slew rate may limit performance in high-speed applications.

Working Principles

The TLC2264CDG4 is based on a standard operational amplifier architecture. It utilizes differential inputs to amplify the voltage difference between the non-inverting and inverting terminals. The amplified output is then fed back to the inverting terminal through a feedback network, which sets the gain and stability of the amplifier.

Detailed Application Field Plans

The TLC2264CDG4 is commonly used in various applications, including but not limited to:

  1. Audio Amplification: The low-power consumption and rail-to-rail output make it suitable for audio amplifiers in portable devices.
  2. Sensor Signal Conditioning: The op-amp's low input bias current and wide operating temperature range make it ideal for amplifying and conditioning signals from sensors.
  3. Battery-Powered Systems: The low-power characteristics of the TLC2264CDG4 make it well-suited for use in battery-powered systems, such as handheld instruments or wireless communication devices.

Detailed and Complete Alternative Models

Some alternative models to the TLC2264CDG4 include:

  1. LM324: A widely-used quad operational amplifier with similar specifications.
  2. MCP6004: Low-power quad op-amp with rail-to-rail input and output.
  3. TL074: High-performance quad JFET-input operational amplifier.

These alternative models offer similar functionality and can be considered as substitutes depending on specific requirements.

Word count: 408 words

Seznam 10 běžných otázek a odpovědí souvisejících s aplikací TLC2264CDG4 v technických řešeních

Sure! Here are 10 common questions and answers related to the application of TLC2264CDG4 in technical solutions:

  1. Q: What is TLC2264CDG4? A: TLC2264CDG4 is a quad operational amplifier (op-amp) integrated circuit that is commonly used in various electronic applications.

  2. Q: What is the supply voltage range for TLC2264CDG4? A: The supply voltage range for TLC2264CDG4 is typically between 3V and 16V.

  3. Q: What is the maximum output current of TLC2264CDG4? A: The maximum output current of TLC2264CDG4 is typically around 40mA.

  4. Q: Can TLC2264CDG4 be used in single-supply applications? A: Yes, TLC2264CDG4 can be used in both single-supply and dual-supply applications.

  5. Q: What is the input offset voltage of TLC2264CDG4? A: The input offset voltage of TLC2264CDG4 is typically around 1mV.

  6. Q: Is TLC2264CDG4 suitable for low-power applications? A: Yes, TLC2264CDG4 is designed for low-power consumption, making it suitable for battery-powered devices or other low-power applications.

  7. Q: What is the typical gain bandwidth product of TLC2264CDG4? A: The typical gain bandwidth product of TLC2264CDG4 is around 1MHz.

  8. Q: Can TLC2264CDG4 operate at high temperatures? A: Yes, TLC2264CDG4 has a wide temperature range and can operate reliably at high temperatures up to 125°C.

  9. Q: What is the input common-mode voltage range of TLC2264CDG4? A: The input common-mode voltage range of TLC2264CDG4 typically extends from the negative supply voltage to within 1.5V of the positive supply voltage.

  10. Q: Can TLC2264CDG4 be used in audio applications? A: Yes, TLC2264CDG4 can be used in audio applications such as audio amplifiers, equalizers, or audio mixers due to its low distortion and wide bandwidth characteristics.

Please note that the specific values mentioned above are typical values and may vary depending on the manufacturer's specifications.