STMicroelectronics
Obrázek může být reprezentace.
Viz Specifikace pro podrobnosti o produktu.
STP180N55F3
Zobrazit detail DataSheets

STP180N55F3

Introduction

The STP180N55F3 is a power MOSFET belonging to the category of electronic components. It is widely used in various applications due to its unique characteristics and functional features.

Basic Information Overview

  • Category: Power MOSFET
  • Use: The STP180N55F3 is used as a switching device in power electronics applications.
  • Characteristics: This MOSFET offers low on-state resistance, high switching speed, and low gate charge, making it suitable for high-efficiency power conversion.
  • Package: The STP180N55F3 is typically available in a TO-220 package.
  • Essence: Its essence lies in providing efficient power switching capabilities.
  • Packaging/Quantity: It is commonly packaged in reels or tubes containing multiple units.

Specifications

  • Voltage Rating: 55V
  • Current Rating: 180A
  • On-State Resistance: 0.0035 ohms
  • Gate-Source Voltage (Max): ±20V
  • Operating Temperature Range: -55°C to 175°C

Detailed Pin Configuration

The STP180N55F3 typically has three pins: 1. Gate (G): Used to control the switching operation. 2. Drain (D): Connects to the load or power supply. 3. Source (S): Connected to the ground or common reference point.

Functional Features

  • Low On-State Resistance: Enables minimal power dissipation during conduction.
  • High Switching Speed: Facilitates rapid switching transitions, reducing switching losses.
  • Low Gate Charge: Allows for efficient control of the MOSFET.

Advantages and Disadvantages

Advantages

  • High efficiency in power conversion applications.
  • Low power dissipation due to low on-state resistance.
  • Fast switching speed leading to reduced switching losses.

Disadvantages

  • Sensitive to voltage spikes and overcurrent conditions.
  • Requires careful consideration of driving circuitry to avoid damage.

Working Principles

The STP180N55F3 operates based on the principle of field-effect transistors, where the voltage applied to the gate terminal controls the flow of current between the drain and source terminals. By modulating the gate-source voltage, the MOSFET can efficiently switch high-power loads.

Detailed Application Field Plans

The STP180N55F3 finds extensive use in the following application fields: - Switched-Mode Power Supplies: Utilized in high-efficiency power supplies for various electronic devices. - Motor Control: Employed in motor drive circuits for controlling large electric motors. - Inverters: Integrated into inverters for renewable energy systems such as solar and wind power.

Detailed and Complete Alternative Models

Some alternative models to the STP180N55F3 include: - IRF3205: Similar specifications and package type. - IXFH180N10T: Offers comparable performance in power switching applications. - FDMS86181: Suitable for high-current switching with similar characteristics.

In conclusion, the STP180N55F3 power MOSFET serves as a crucial component in power electronics, offering high efficiency and fast switching capabilities across various applications.

[Word Count: 443]

Seznam 10 běžných otázek a odpovědí souvisejících s aplikací STP180N55F3 v technických řešeních

  1. What is the maximum drain-source voltage rating of STP180N55F3?

    • The maximum drain-source voltage rating of STP180N55F3 is 55 volts.

  2. What is the continuous drain current rating of STP180N55F3?

    • The continuous drain current rating of STP180N55F3 is 180 amperes.

  3. What is the on-resistance of STP180N55F3?

    • The on-resistance of STP180N55F3 is typically 0.0035 ohms.

  4. What is the gate threshold voltage of STP180N55F3?

    • The gate threshold voltage of STP180N55F3 is typically 2 to 4 volts.

  5. What is the power dissipation of STP180N55F3?

    • The power dissipation of STP180N55F3 is typically 300 watts.

  6. What are the typical applications for STP180N55F3?

    • STP180N55F3 is commonly used in high-power switching applications, motor control, and power supplies.

  7. What is the operating temperature range of STP180N55F3?

    • The operating temperature range of STP180N55F3 is typically -55°C to 175°C.

  8. Is STP180N55F3 suitable for automotive applications?

    • Yes, STP180N55F3 is suitable for automotive applications due to its high current and voltage ratings.

  9. Does STP180N55F3 require a heat sink for operation?

    • Depending on the application and power dissipation, a heat sink may be required for optimal performance of STP180N55F3.

  10. What are the key advantages of using STP180N55F3 in technical solutions?

    • The key advantages of using STP180N55F3 include its high current and voltage ratings, low on-resistance, and suitability for high-power applications.