Obrázek může být reprezentace.
Viz Specifikace pro podrobnosti o produktu.
AT25080B-WWU11L

AT25080B-WWU11L Encyclopedia Entry

Product Overview

The AT25080B-WWU11L belongs to the category of Serial EEPROM (Electrically Erasable Programmable Read-Only Memory) and is commonly used for storing small amounts of data in various electronic devices. This EEPROM offers characteristics such as low power consumption, high reliability, and a wide operating voltage range. It is typically packaged in a small form factor, making it suitable for space-constrained applications. The essence of the AT25080B-WWU11L lies in its ability to retain stored data even when the power is turned off. It is commonly available in tape and reel packaging with varying quantities based on customer requirements.

Specifications

  • Storage Capacity: 8 Kbits (1 Kbyte)
  • Interface: SPI (Serial Peripheral Interface)
  • Operating Voltage Range: 1.7V to 5.5V
  • Operating Temperature Range: -40°C to 85°C
  • Package Type: 8-lead SOIC (Small Outline Integrated Circuit)

Detailed Pin Configuration

The AT25080B-WWU11L features an 8-pin configuration: 1. Chip Select (/CS) 2. Serial Data Input/Output (DI/DO) 3. Serial Clock (SCK) 4. Ground (GND) 5. Write Protect (/WP) 6. VCC Power Supply 7. Not Connected (NC) 8. Serial Data Out (DO)

Functional Features

  • Byte and Page Write Modes
  • Self-timed Write Cycle
  • High-Speed Clock Frequency (up to 10 MHz)
  • Software and Hardware Write Protection
  • Sequential Read Operation

Advantages and Disadvantages

Advantages

  • Low Power Consumption
  • High Reliability
  • Wide Operating Voltage Range
  • Small Form Factor

Disadvantages

  • Limited Storage Capacity
  • Slower Write Speed compared to other memory technologies

Working Principles

The AT25080B-WWU11L operates by using an electric field to apply voltage to specific parts of the memory cell, allowing data to be written or erased. When reading data, the stored charge in the memory cells is detected, enabling the retrieval of the stored information.

Detailed Application Field Plans

The AT25080B-WWU11L is widely used in applications such as: - Consumer Electronics (e.g., smart TVs, set-top boxes) - Automotive Systems (e.g., engine control units, infotainment systems) - Industrial Control Systems (e.g., programmable logic controllers, sensors)

Detailed and Complete Alternative Models

Some alternative models to the AT25080B-WWU11L include: - AT25128B-WWU11L: 32 Kbit Serial EEPROM - AT24C02C-SSHM-T: 2 Kbit I2C EEPROM - CAT24C08WI-GT3: 8 Kbit I2C EEPROM

In conclusion, the AT25080B-WWU11L Serial EEPROM offers a reliable and efficient solution for data storage in various electronic applications, despite its limitations in storage capacity and write speed. Its wide operating voltage range and small form factor make it a versatile choice for designers seeking non-volatile memory solutions.

[Word Count: 443]

Seznam 10 běžných otázek a odpovědí souvisejících s aplikací AT25080B-WWU11L v technických řešeních

  1. What is the AT25080B-WWU11L?

    • The AT25080B-WWU11L is a serial EEPROM (Electrically Erasable Programmable Read-Only Memory) chip manufactured by Adesto Technologies. It is commonly used for storing small amounts of non-volatile data in various technical solutions.
  2. What are the key features of the AT25080B-WWU11L?

    • The AT25080B-WWU11L features an 8-Kbit memory array, SPI interface, low power consumption, and a wide voltage operation range, making it suitable for a variety of applications.
  3. How is the AT25080B-WWU11L typically used in technical solutions?

    • The AT25080B-WWU11L is often used to store configuration settings, calibration data, or other small amounts of non-volatile information in embedded systems, IoT devices, industrial equipment, and consumer electronics.
  4. What are the advantages of using the AT25080B-WWU11L in technical solutions?

    • Some advantages include its small form factor, low power consumption, high reliability, and ease of integration with microcontrollers and other digital systems.
  5. What are the typical operating conditions for the AT25080B-WWU11L?

    • The AT25080B-WWU11L operates within a wide voltage range (1.7V to 5.5V) and at temperatures ranging from -40°C to 85°C, making it suitable for diverse environmental conditions.
  6. How do I interface with the AT25080B-WWU11L in my design?

    • The AT25080B-WWU11L uses a Serial Peripheral Interface (SPI) for communication, and the datasheet provides detailed information on how to connect and communicate with the chip.
  7. Are there any specific considerations for programming or erasing data on the AT25080B-WWU11L?

    • The AT25080B-WWU11L supports byte and page write operations, and the datasheet outlines the necessary commands and timing requirements for programming and erasing data.
  8. Can the AT25080B-WWU11L be used in battery-powered devices?

    • Yes, the AT25080B-WWU11L's low power consumption makes it well-suited for use in battery-powered devices, helping to extend the overall battery life.
  9. What are some common challenges when integrating the AT25080B-WWU11L into a technical solution?

    • Challenges may include ensuring proper signal integrity in the SPI communication, managing the chip select and other control signals, and addressing any specific timing requirements.
  10. Where can I find additional resources and support for working with the AT25080B-WWU11L?

    • Adesto Technologies provides datasheets, application notes, and technical support to assist with integrating the AT25080B-WWU11L into technical solutions. Additionally, online forums and communities may offer valuable insights and troubleshooting tips.