AT24C11-10TI-2.7

Product Overview

Category

AT24C11-10TI-2.7 belongs to the category of EEPROM (Electrically Erasable Programmable Read-Only Memory) chips.

Use

This product is primarily used for non-volatile data storage in various electronic devices, such as microcontrollers, computers, and consumer electronics.

Characteristics

• Non-volatile: The stored data remains intact even when power is removed.
• Electrically erasable: The memory can be erased and reprogrammed electrically.
• High density: The chip offers a large storage capacity.
• Low power consumption: It operates at low voltage levels, minimizing power requirements.
• Reliable: The data retention capability ensures long-term reliability.

Package

AT24C11-10TI-2.7 is available in a standard 8-pin DIP (Dual Inline Package) or SOIC (Small Outline Integrated Circuit) package.

Essence

The essence of AT24C11-10TI-2.7 lies in its ability to provide reliable and non-volatile data storage in electronic devices.

Packaging/Quantity

This product is typically packaged in reels or tubes, with quantities varying based on customer requirements.

Specifications

• Operating Voltage: 2.7V - 5.5V
• Memory Size: 1,024 bits (128 bytes)
• I2C Bus Interface: Compatible with I2C protocol
• Write Cycle Time: 10ms (maximum)
• Data Retention: Up to 100 years
• Operating Temperature Range: -40°C to +85°C

Detailed Pin Configuration

1. A0: Address Input
2. A1: Address Input
3. A2: Address Input
4. GND: Ground
5. SDA: Serial Data Input/Output
6. SCL: Serial Clock Input
7. WP: Write Protect
8. VCC: Power Supply

Functional Features

• Random Access: Allows reading and writing of data at any memory location.
• Byte-Level Operations: Supports individual byte read and write operations.
• Page Write Mode: Enables multiple bytes to be written in a single operation, improving efficiency.
• Write Protection: The WP pin can be used to protect the memory from accidental writes.
• Software and Hardware Compatibility: Compatible with various microcontrollers and I2C interfaces.

Advantages and Disadvantages

Advantages

• Non-volatile storage ensures data integrity.
• High-density memory for efficient data storage.
• Low power consumption prolongs battery life.
• Reliable performance with long data retention.
• Compatibility with standard I2C protocol simplifies integration.

Disadvantages

• Limited storage capacity compared to other memory technologies.
• Slower write cycle time may impact performance in certain applications.
• Vulnerable to electrical disturbances during write operations.

Working Principles

AT24C11-10TI-2.7 utilizes EEPROM technology, which allows data to be stored and retrieved electrically. It consists of a grid of memory cells that can be individually programmed or erased using electrical signals. The memory cells retain their state even when power is removed, ensuring non-volatile storage.

The chip communicates with the host device through the I2C bus interface, enabling easy integration into various systems. Data can be read or written by sending appropriate commands and addresses over the serial interface.

Detailed Application Field Plans

AT24C11-10TI-2.7 finds application in a wide range of electronic devices, including but not limited to: - Microcontrollers - Computers and peripherals - Consumer electronics (e.g., TVs, smartphones, tablets) - Industrial control systems - Automotive electronics - Medical devices

Its ability to provide reliable and non-volatile data storage makes it suitable for applications where data integrity is crucial.

Detailed and Complete Alternative Models

• AT24C01A: 1,024-bit (128-byte) EEPROM with similar specifications.
• AT24C02: 2,048-bit (256-byte) EEPROM with higher storage capacity.
• AT24C16: 16,384-bit (2,048-byte) EEPROM with increased memory size.
• AT24C64: 65,536-bit (8,192-byte) EEPROM with larger storage capacity.

These alternative models offer varying memory sizes to cater to different application requirements.

In conclusion, AT24C11-10TI-2.7 is an EEPROM chip that provides reliable and non-volatile data storage in electronic devices. Its high density, low power consumption, and compatibility with standard interfaces make it a versatile choice for various applications. However, its limited storage capacity and slower write cycle time should be considered when selecting the appropriate memory solution.