Category: Integrated Circuit (IC)
Use: Non-volatile Serial EEPROM Memory
Characteristics: - Low-power CMOS technology - 32K x 8-bit organization - SPI compatible serial interface - 2.5V to 5.5V operating voltage range - 1 MHz clock rate - 100,000 erase/write cycles endurance - Data retention > 200 years - 8-pin PDIP package
Essence: The 25LC320-I/P is a non-volatile memory chip that provides reliable and long-term storage of data in various electronic devices.
Packaging/Quantity: The 25LC320-I/P is available in an 8-pin Plastic Dual Inline Package (PDIP). It is typically sold in reels or tubes containing multiple units.
The 25LC320-I/P has the following pin configuration:
| Pin Number | Pin Name | Description | |------------|----------|-------------| | 1 | CS | Chip Select | | 2 | SO | Serial Data Output | | 3 | WP | Write Protect | | 4 | VSS | Ground | | 5 | SI | Serial Data Input | | 6 | SCK | Serial Clock | | 7 | HOLD | Hold Input | | 8 | VCC | Power Supply |
Advantages: - Non-volatile memory ensures data retention even during power loss. - Compact size and easy integration into various electronic devices. - Low power consumption extends battery life. - High endurance allows for frequent read/write operations. - Wide operating voltage range provides flexibility in different applications.
Disadvantages: - Limited storage capacity compared to larger EEPROM chips. - Slower data transfer rate compared to some other memory technologies. - Relatively higher cost per kilobyte of storage compared to other memory options.
The 25LC320-I/P utilizes non-volatile Electrically Erasable Programmable Read-Only Memory (EEPROM) technology. It stores data in a grid of memory cells that can be electrically programmed and erased. The chip communicates with a microcontroller or other devices using the SPI protocol, allowing for easy integration into various systems. Data can be written, read, and erased from the memory using specific commands sent through the serial interface.
The 25LC320-I/P is widely used in various electronic devices and systems, including but not limited to: - Consumer electronics - Industrial automation - Automotive applications - Medical devices - Communication equipment - Smart home devices
In consumer electronics, it can be found in products such as digital cameras, set-top boxes, and portable media players. In industrial automation, it is used for storing configuration data, calibration values, and event logs. Automotive applications include storing vehicle parameters, firmware updates, and diagnostic information. Medical devices utilize it for patient data storage and device configuration. Communication equipment relies on it for storing network settings and firmware. Smart home devices use it for storing user preferences and device configurations.
These alternative models offer increased memory capacity while maintaining compatibility with the 25LC320-I/P in terms of pin configuration and
What is the maximum clock frequency for 25LC320-I/P?
- The maximum clock frequency for 25LC320-I/P is 10 MHz.
What is the operating voltage range for 25LC320-I/P?
- The operating voltage range for 25LC320-I/P is 2.5V to 5.5V.
Can 25LC320-I/P be used in automotive applications?
- Yes, 25LC320-I/P is suitable for automotive applications.
What is the typical write time for 25LC320-I/P?
- The typical write time for 25LC320-I/P is 5 ms.
Is 25LC320-I/P compatible with SPI interface?
- Yes, 25LC320-I/P is compatible with SPI interface.
What is the temperature range for 25LC320-I/P?
- The temperature range for 25LC320-I/P is -40°C to +85°C.
Does 25LC320-I/P support partial page writes?
- Yes, 25LC320-I/P supports partial page writes.
Can 25LC320-I/P be used in industrial control systems?
- Yes, 25LC320-I/P is suitable for use in industrial control systems.
What is the typical standby current for 25LC320-I/P?
- The typical standby current for 25LC320-I/P is 1 µA.
Is 25LC320-I/P RoHS compliant?
- Yes, 25LC320-I/P is RoHS compliant.